Драйвер usb ross tech hex usb для windows
Драйвер usb ross tech hex usb для windows
Diagnostic Software for VW-Audi Group Cars
881 Sumneytown Pike, Lansdale PA 19446, USA
Virtual COM Port Drivers for Ross-Tech USB Interfaces
Older Ross-Tech RS-232 Serial interfaces can be set to power up as «dumb K-Line pass through» interfaces. This allowed those old Serial interfaces to be compatible with a wide variety of third-party applications which expect a «K-line pass-through» serial interface. However, our USB interfaces present additional challenges. Early in their development, we found a number of technical advantages to using a «direct» USB driver which bypasses the Windows Serial drivers entirely. Hence the USB drivers that ship with VCDS do not emulate a serial COM port and cannot be used with applications that expect to communicate via a serial port.
NOTE: The following applies to our legacy USB interfaces (HEX-USB, KII-USB and HEX-USB+CAN). It does NOT apply to our current HEX-V2 or HEX-NET interfaces. These new interfaces do not use a USB UART chip and cannot be be used for «dumb K-line pass-through»!
In order to facilitate the use of third-party applications which expect to communicate with a serial interface, drivers that emulate a COM port are available. However, anyone thinking about using them needs to be aware of the following points:
We do not offer installation support for these drivers. They should be used only by someone who is competent/comfortable installing (and possible uninstalling) USB drivers on his PC.
We cannot offer any support for third-party software, nor any guarantee that it will work correctly with these drivers. Of course, the same would apply with a serial interface as well.
That said, here some installation notes:
These drivers are compatible with Windows 2000 and newer. They should work with W2K, XP-32, XP-64, Vista-32 and Vista-64. We do not have any VCP drivers for Windows 98!
Unzip the contents of the download into a new folder.
With an interface plugged in, find it in Device Manager, right-click it, and select Update Driver.
Depending on what drivers your system already has installed, you may have to «force» these by telling the wizard not to search, but to let you specify what driver to install, then doing the Have Disk and Browse thing.
There’s also the possibility that the Virtual COM Port won’t install automatically. We’ve found no real pattern why it does on some systems and not on others. If it does not, find the interface in Device > Manager. The name should show «. with VCP». Open the properties sheet, click the Advanced tab, and make sure Load VCP is checked. Once checked, disconnect and re-connect the interface.
Once the USB Serial Port is installed, you may need to change the COM Port Number (depending on how high a number the applications supports). Device Manager, Properties sheet for the USB Serial Port, Port Settings tab, Advanced button. The COM Port Number may change if you plug the interface into a different USB port, so I’d recommend always using the same USB port.
VCDS should continue to work fine with these drivers installed. Leave VCDS set to USB, not a Virtual COM Port!
Assuming you’ve read and understand all of the above, you can download the «Virtual COM Port» drivers here:
Unless otherwise noted, all content on this site is Copyright (c) 2000-2017 by Ross-Tech LLC. All rights reserved.
«VCDS», «VCDS-Mobile» and «HEX-NET» are Registered Trademarks of Ross-Tech, LLC.
Ross-Tech is not affiliated with the Volkswagen Group in any way.
Драйвер usb ross tech hex usb для windows
Diagnostic Software for VW-Audi Group Cars
881 Sumneytown Pike, Lansdale PA 19446, USA
USB Driver Installation Instructions for VCDS and Windows XP
Notes: VCDS should install the drivers automatically. These instructions are only to be used in case the automatic driver installation is not successful. These instructions are for Windows XP. Installation under Windows 98/ME/2000 is similar, but not necessarily identical.
Make sure you have already downloaded and installed VCDS on your PC before following these instructions.
If you haven’t yet downloaded VCDS, then click HERE to open our download page in a new window.
Allow the software you just downloaded to install itself on your PC.
If you choose to install it someplace other than the default location,
make a note of folder you’re installing it to.
Plug your Ross-Tech USB Interface to your PC’s USB port (It is not necessary to connect the interface to a car yet). A message like this should appear on your PC’s Taskbar:
NOTE: If the new Hardware Found Wizard popup does not appear when you plug in your interface, go into Device Manager and look for the interface. In Windows XP, you can typically find the Device Manager by RIGHT-CLICKING on My Computer then selecting Manage. Your Ross-Tech USB Interface should be under Universal Serial Bus (USB) Controllers or under Other Devices. If it’s there, Right-Click it and then select Update Driver. Then you can start at Step 4 in the instructions below.
The New Hardware Found Wizard should appear:
On the screen above, select «Install from a list or specific location (Advanced)»
then click the [Next >] button.
The following dialog should appear:
On the screen above:
Select «Search for the best driver in these locations»
Check «Include this location in the search:»
Use the [Browse] button to find the VCDS folder
(Usually C:\ross-tech\VCDS\
unless you chose a different folder when you installed the software)
Click [OK]
The following dialog should appear:
Click the [Next >] button.
If you get a Windows message stating «This hardware will not be installed. Contact your system administrator» then you need to do the following
A) Login to Windows with Administrator rights.
C) Select Warn and choose «Prompt me each time to choose an action.»
D) Next, repeat the driver installation starting in Step 3.
The following dialog should appear:
Click the [Finish] button to complete the installation.
Start VCDS.
Click the [Options] button.
In the «Select COM Port» box, select USB.
Click the [Test] button.
The results should look like this (it may have additional information in the Port Test dialog).
Click [OK] and click [Save]
Go test it on a car. 🙂
Note: If you run into problems with this procedure (make sure to try the suggestions in step 3), feel free to Contact us while you are in front of your PC, connected to your vehicle.
VCDS (VAG-COM) HEX-CAN 11.11.3 и адаптер на чипе NEC D79F8513A.
О машине: Audi A3 (8P) 2010 года tdw
Адаптер VCSD (VAG-COM) HEX-CAN 11.11.3 позволяет диагностировать авто до 2013г. выпуска. Существует несколько разновидностей данного кабеля. Отличаются они чипом на котором собран адаптер.
Внимание! Адаптеры рассчитаны именно на те версии, с которыми поставляются. Более поздние версии убивают адаптеры!
Почему это происходит? Каждый шнурок при производстве обучают обманывать только определенную версию п.о.(обычно последнюю, самую стабильную или менее защищенную). В свою очередь, производитель Ross-Tech в новые версии программы встраивает механизмы, определяющие «адаптер-клон» и стирающие его память(убивающие его).
Автоадаптер VAG-Com HEX-CAN на чипе NEC D79F8513A.
Что бы определить чип на котором собран адаптер, достаточно его разобрать и прочитать маркировку микросхем.
По отзывам кабель на данном чипе работает довольно стабильно. Основным его недостатком является отсутствие п.о. на русском языке.
Внимание! П.О. для данного кабеля на русском языке нет и не будет. Если это критично то лучше приобрести более дорогие аналоги «Вася» или «Автоадаптер».
Кабель, программа, подключение.
VCDS (VAG-COM) HEX-CAN 11.11.3 Скачать
1. Подключаем кабель к ПК.
3. После успешной установки драйвера в разделе «Контроллеры USB» появится новое устройство Ross-Tech Direct Interface.
4. Устанавливаем программу VCDS-Release-11.11.3 (dr.Web может поругаться на вирусы, игнорируем).
5. Запускаем программу. при первом запуске все вкладки не активны. Выбираем Options.
6. Выбираем порт USB, нажимаем Test.
8. Теперь все вкладки активны, можно приступать к диагностике авто.
Часовой пояс: UTC+03:00
| Начать новую тему Ответить на тему | Страница 1 из 1 | [ 15 сообщений ] |
|
