How to load windows in safe mode

Advanced startup options (including safe mode)

The Advanced Boot Options screen lets you start Windows in advanced troubleshooting modes. You can access the menu by turning on your computer and pressing the F8 key before Windows starts.

Some options, such as safe mode, start Windows in a limited state, where only the bare essentials are started. If a problem doesn’t reappear when you start in safe mode, you can eliminate the default settings and basic device drivers and services as possible causes. Other options start Windows with advanced features intended for use by system administrators and IT professionals. For more information, go to the Microsoft website for IT professionals.

Repair Your Computer

Shows a list of system recovery tools you can use to repair startup problems, run diagnostics, or restore your system. This option is available only if the tools are installed on your computer’s hard disk. If you have a Windows installation disc, the system recovery tools are located on that disc.

Safe Mode

Starts Windows with a minimal set of drivers and services.

To start in safe mode:

Do one of the following:

If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you’ll need to try again by waiting until the Windows logon prompt appears, and then shutting down and restarting your computer.

If your computer has more than one operating system, use the arrow keys to highlight the operating system you want to start in safe mode, and then press F8.

On the Advanced Boot Options screen, use the arrow keys to highlight the safe mode option you want, and then press Enter.

Log on to your computer with a user account that has administrator rights.

Safe Mode with Networking. Starts Windows in safe mode and includes the network drivers and services needed to access the Internet or other computers on your network.

Safe Mode with Command Prompt. Starts Windows in safe mode with a command prompt window instead of the usual Windows interface. This option is intended for IT professionals and administrators.

Enable Boot Logging. Creates a file, ntbtlog.txt, that lists all the drivers that are installed during startup and that might be useful for advanced troubleshooting.

Enable low-resolution video (640×480). Starts Windows using your current video driver and using low resolution and refresh rate settings. You can use this mode to reset your display settings. For more information, see Change your screen resolution.

Last Known Good Configuration (advanced). Starts Windows with the last registry and driver configuration that worked successfully.

Directory Services Restore Mode. Starts Windows domain controller running Active Directory so that the directory service can be restored. This option is intended for IT professionals and administrators.

Debugging Mode. Starts Windows in an advanced troubleshooting mode intended for IT professionals and system administrators.

Disable automatic restart on system failure. Prevents Windows from automatically restarting if an error causes Windows to fail. Choose this option only if Windows is stuck in a loop where Windows fails, attempts to restart, and fails again repeatedly.

Disable Driver Signature Enforcement. Allows drivers containing improper signatures to be installed.

Start Windows Normally. Starts Windows in its normal mode.

Источник

Start your PC in safe mode in Windows 10

Safe mode starts Windows in a basic state, using a limited set of files and drivers. If a problem doesn’t happen in safe mode, this means that default settings and basic device drivers aren’t causing the issue. Observing Windows in safe mode enables you to narrow down the source of a problem, and can help you troubleshoot problems on your PC.

There are two versions of safe mode: Safe Mode and Safe Mode with Networking. Safe Mode with Networking adds the network drivers and services you’ll need to access the Internet and other computers on your network.

Select from the following sections to find out how to start your PC in safe mode from Settings, from the sign-in screen, or from a black or blank screen.

Under Advanced startup, select Restart now.

After your PC restarts to the Choose an option screen, select Troubleshoot > Advanced options > Startup Settings > Restart. You may be asked to enter your BitLocker recovery key.

After your PC restarts, you’ll see a list of options. Select 4 or press F4 to start your PC in Safe Mode. Or if you’ll need to use the Internet, select 5 or press F5 for Safe Mode with Networking.

When you can’t open Settings to get into safe mode, restart your device from the Windows sign-in screen.

After your PC restarts to the Choose an option screen, select Troubleshoot > Advanced options > Startup Settings > Restart. You may be asked to enter your BitLocker recovery key.

After your PC restarts, you’ll see a list of options. Select 4 or F4 to start your PC in safe mode. Or if you’ll need to use the Internet, select 5 or F5 for Safe Mode with Networking.

Note: If you’ve encrypted your device, you’ll need your BitLocker key to start in safe mode.

Before you enter safe mode, you need to enter the Windows Recovery Environment (winRE). To do this, you will repeatedly turn your device off, then on:

Hold down the power button for 10 seconds to turn off your device.

Press the power button again to turn on your device.

On the first sign that Windows has started (for example, some devices show the manufacturer’s logo when restarting) hold down the power button for 10 seconds to turn off your device.

Press the power button again to turn on your device.

When Windows restarts, hold down the power button for 10 seconds to turn off your device.

Press the power button again to turn on your device.

Allow your device to fully restart. You will enter winRE.

Now that you are in winRE, you will follow these steps to take you to safe mode:

On the Choose an option screen, select Troubleshoot > Advanced options > Startup Settings > Restart.

After your device restarts, you’ll see a list of options. Select option 5 from the list or press F5 for Safe Mode with Networking.

If you need more info on a black or blank screen error, see Troubleshoot black or blank screen errors.

Notes: If you need to exit safe mode, simply restart your device, or:

Press the Windows logo key + R.

Type msconfig in the Open box and then select OK.

Select the Boot tab.

Under Boot options, clear the Safe boot checkbox.

Источник

How to Boot Safe Mode Windows 10, 8, 7 (7 ways)

What is Safe Mode and how to boot Safe mode Windows.

💡 For Windows 10, 8, 7; for laptop and computer.

Contents

Safe Mode and Options

is a diagnostic mode of a computer operating system. Safe mode is intended to help fix most, if not all problems within an operating system.

Booting in Safe Mode Windows is often used to remove viruses and programs that cannot be removed during normal mode of the Operating System (OS).

Safe Mode Windows 10

In this mode, the minimum set of system programs and services necessary to start the system is loaded.

Starting non-system services from startup and not system programs is ignored.

🔔 The ability to work in this mode is limited.

There are three modes for starting Windows Safe Mode:

Three modes of Safe Mode Windows 10

Safe mode after reboot (Windows 10, 8)

An easy way to reboot Windows in safe mode.

💡 Suitable for Windows 10, 8.

5. In the Troubleshoot window, select the Advanced options;

Troubleshoot

6. In the Advanced options window, select the Startup Settings;

Advanced options

7. In the Startup Setting window, click the Restart button;

Startup Settings

8. After restarting your computer, In the Boot Options window (Advanced Boot Options), select the required Windows boot mode.

Advanced Boot Options for Windows 10

Windows will boot in Safe mode.

To exit Safe Mode, restart your computer.

Using msconfig (Windows 10, 8, 7)

We use the msconfig utility to boot Windows in safe mode.

💡 Suitable for Windows 10, 8, 7.

To exit Safe mode, restart your computer.

🔔 The msconfig utility provides additional options for starting the computer (disabling the launch of services and applications).

Enable Advanced boot options (Windows 10, 8)

💡 Suitable for Windows 10, 8.

In Windows 10, 8, the call to this menu with the F8 button must be turned on manually.

Close the command prompt window, restart the computer.

Before loading the operating system, press the F8 button, the Advanced boot options menu opens, where we can choose several options for starting Safe Mode or other Windows boot options.

🔔 If you have a laptop, you may have to press the Fn + F8 key combination.

Advanced Boot Options for Windows 10

Safe Mode from System Restore (Windows 10, 8)

💡 Suitable for Windows 10, 8.

You can boot Safe Mode Windows 10, 8 from Recovery mode, after an incorrect OS boot.

After three consecutive power outages when loading Windows 10, 8, the system will start to boot Recovery mode.

Recovery mode Windows 10, 8

Select See advanced repair options recovery options.

Further, the launch of Safe Mode will occur as in paragraph – Safe Mode after reboot (Windows 10, 8).

🔔 We dont recommend using this method of loading Windows Safe Mode, as this can cause permanent damage to the system!

Safe mode from the command prompt (bcdedit)

The bcdedit command changes persistent Windows boot options. After enabling Safe Mode, enter the command to change the configuration and disable booting into Safe Mode.

You can also use the bcdedit command in the command prompt in Windows Recovery mode.

You can boot Windows in Safe Mode by running the bcdedit command in the Command Prompt running with administrator rights.

Enable Safe Mode:

Enable Safe Mode with Networking:

Enable Safe Mode with Command Prompt (enter two commands):

Restart your computer to apply the new configuration settings.

To disable booting Safe Mode, in Windows configuration, run:

Safe mode using shutdown utility

The shutdown utility is a built-in Windows program that allows you to restart, shutdown, hibernate, or end a user session.

After rebooting, in the System Restore window, select the required option.

Learn more about the startup parameters of the shutdown utility – here.

I hope you were able to boot Windows in Safe Mode in a convenient way.

How to boot Windows Safe Mode:

Hold the SHIFT button and press Reset button. More…

Run the msconfig utility, select the Safe Mode – Minimal option. More…

Use the bcdedit command to enable the Advanced boot menu and the press F8 button (as on Windows 7, XP) to call up the menu, when the Windows boot. More…

Three times, power off the system to enable the Recovery mode and boot Windows Safe Mode. More…

These were the available options for boot Safe Mode Windows 10, 8, 7.

🟢 How to boot Safe Mode in Windows 10, 8, 7 was discussed in this article. I hope you can now configure Windows to start in Safe Mode. However, if you run into any problems, do not hesitate to write in the comments. I will try to help.

Источник

Steps to Boot Windows 10 in Safe Mode [with Pictures]

Last Updated: 1 year ago

In Windows 10, if you want to start Safe Mode with the F8 key, you have to set it up first. Read on to find out why and how, and to learn other ways to access Safe Mode in Windows 10.

Three other ways to access Safe Mode in Windows 10

TIP: If you’re tired of Windows problems that force you to start in Safe Mode, scroll down to this suggestion.

Why can’t you access the Safe Mode using F8?

On previous versions of Windows such as Windows 7, at the beginning of the boot, you’re able to press the F8 key to access the Advanced Boot Options menu, where you can enable Safe Mode. But on Windows 10, the F8 key doesn’t work any more. No matter how many times you’ve tried. You must be wondering why this happens. Is it removed from Windows 10?

Actually, F8 key is still available to access the Advanced Boot Options menu on Windows 10. But starting from Windows 8 (F8 doesn’t work on Windows 8, either.), in order to have faster boot time, Microsoft has disabled this feature by default. That is to say Windows 10 boots too fast to have any time to let anything interrupt. If you want to use the F8 key to access the Safe Mode, you need to enable the feature manually.

How can you get F8 work again?

F8 boot menu feature is disabled on Windows 10 by default. The good news is you can get it work again with the Boot Configuration Data (BCD) Edit command. BCD Edit is a tool written to control how the operating system is started. You can use it to enable F8 boot menu easily. Just follow these steps:

1) On your keyboard, press Windows logo key and R key at the same time to invoke the run command.

2) Type cmd then press Ctrl+Shift+Enter to open an administrator command prompt. (Don’t just press Enter or click OK as that won’t open the command prompt in an administrator mode.)

3) Copy the following command and paste it in the Command Prompt. Then on your keyboard, press the Enter key.

bcdedit /set bootmenupolicy legacy

4) Reboot your PC. Before the Windows logo appears, press F8 to access the Boot Options menu (see below screenshot). Then select Safe Mode.

Note: You can get F8 work again only when you’re able to access Windows. If you can’t start Windows normally, you need to use other effective way.

How to boot into Safe Mode in Windows 10?

Except F8, there are other numerous ways to boot into Safe Mode in Windows 10. In this post, you’ll learn the easiest ways. If you run into a serious problem (for example, blue screen) and can’t start Windows normally, please use Way 1 to enter Safe Mode. If you’re in Windows Normal Mode, please use Way 2. If you boots to the login screen (you may call it sign-in screen), please use Way 3.

Way 1: Enter Safe Mode when you can’t boot normally

Safe Mode loads with a minimum set of drivers, software and service. Usually, when Windows doesn’t start normally, Safe Mode starts with no problem. It’s useful for you to troubleshoot the problem there.

This way works effectively when you can’t boot Windows 10 normally.

Ensure your PC is off. If your PC is on, turn it off.

Note: This step is aim to bring up Preparing Automatic Repair screen. When Windows doesn’t boot properly, this screen pops up and Windows attempts to fix the problem by itself. If you’ve seen this screen at the first time when you power up the computer, skip this step.

Wait for Windows to diagnose your PC.

Click Advanced options, then the system will bring up the Windows RE (Recovery environment.) screen.

On the Windows RE (Recovery environment) screen, click Troubleshoot.

On the Troubleshoot screen, click Advanced options.

Click Startup Settings to continue.

Click Restart. The computer restarts and another screen opens showing a list of different startup options.

On your keyboard, press the 4 number key to enter Safe Mode without network. (If you need to do some online research after boot into the safe mode, press the 5 number key to enter Safe Mode with network access.)

Way 2: Enter Safe Mode from Normal Mode

If you’ve started Windows normally, you can boot into the safe mode using the System Configuration tool. The System Configuration tool allows you to configure how your PC starts, the boot procedure, the startup items, etc.

Follow below instructions to open the System Configuration tool and set Windows starts in Safe Mode. Just 4 steps:

1) On your keyboard, press the Win+R (Windows logo key and R key) at the same time to invoke the Run box.

2) Type msconfig and click OK. Then the System Configurations will open.

3) When System Configuration opens, click the Boot tab. Under Boot options, check Safe boot then click OK.

4) When you’re prompted to restart your computer to apply these changes, click Restart then you will boot into the Safe Mode.

IMPORTANT: If you want to start Windows 10 in Normal Mode, ensure Safe boot is unchecked.

Way 3: Start Safe Mode from the login screen

If you can boot to the login screen, you can enter Safe Mode from the login screen. The steps are similar with the steps of Way 1.

1) On your keyboard, hold down the Shift key.

2) While holding down the Shift key, on the login screen (you may call it sign in screen), at the bottom right of the corner, click the power button then select Restart. Then Windows will bring up the Windows RE (Recovery environment) screen.

3) On the Windows RE (Recovery environment) screen, click Troubleshoot.

4) On the Troubleshoot screen, click Advanced options.

5) Click Startup Settings.

6) Click Restart. The computer restarts and another screen opens showing a lot of different startup options.

7) On your keyboard, press the 4 number key to enter Safe Mode without network. (If you need to do some online research after booting into the safe mode, press the 5 number key to enter Safe Mode with network access.)

Hope the instructions in this post help you boot into Safe Mode. If you have any ideas or questions, please leave a comment below. Thanks for your reading.

Tired of having to start in Safe Mode?

Windows is a very old technology. Sure, Windows 10 is relatively new, but it’s still just the latest iteration of a decades-old operating system, designed for a bygone era (pre-internet).

Now that we have the internet, fast connection speeds, free cloud storage, and endless web apps (like Gmail, Google Docs, Slack, Facebook, Dropbox and Spotify), the entire Windows way of doing things – with locally installed programs and local file storage – is totally outdated.

Why is that a problem? Because when you’re constantly installing uncontrolled third-party programs, you’re constantly opening the door to viruses and other malware. (And Windows’ insecure permission system compounds this problem.)

Plus the way Windows manages installed software and hardware has always been a problem. If your computer shuts down unexpectedly, or a program installs, uninstalls or updates incorrectly, you can get ‘registry’ corruptions. That’s why Windows PCs always slow down and become unstable over time.

Also because everything’s installed and saved locally, it doesn’t take long before you run out of disk space, and your disk gets fragmented, which makes everything even slower and more unstable.

For most people, the simplest way to solve Windows problems is to ditch Windows altogether, and switch to a faster, more reliable, more secure, easier to use and cheaper operating system…

ChromeOS feels much like Windows, but instead of installing heaps of programs to email, chat, browse the internet, write documents, do school presentations, create spreadsheets, and whatever else you normally do on a computer, you use web apps. You don’t need to install anything at all.

That means you don’t have virus and malware problems, and your computer doesn’t slow down over time, or become unstable.

Источник